Lines Matching refs:console
14 the console before standard serial driver is probed. The console is
33 bool "Support for console on AMBA serial port"
38 console (the system console is the device which receives all kernel
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
60 bool "Support for console on AMBA serial port"
66 console (the system console is the device which receives all kernel
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
77 bool "Early console using ARM semihosting"
83 Support for early debug console using ARM semihosting. This enables
84 the console before standard serial driver is probed. This is enabled
85 with "earlycon=smh" on the kernel command line. The console is
104 bool "Support for console on a BCM1xxx DUART serial port"
110 system console (the system console is the device which receives all
126 bool "Support for console on AT91 / AT32 serial port"
131 AT91 or AT32 processor as the system console (the system
132 console is the device which receives all kernel messages and
163 /dev/, and pass "console=ttyATn" to the kernel.
168 bool "Serial console over KGDB NMI debugger port"
172 as a normal console (assuming that the port is attached to KGDB).
176 This is because this console driver processes the input in NMI
179 Note that since the console interprets input and uses polling
182 use raw console.
194 bool "Support for console on KS8695 (Centaur) serial port"
199 system console (the system console is the device which
212 bool "Support for console on meson"
217 system console (the system console is the device which
231 bool "Support for console on CLPS711X serial port"
235 Even if you say Y here, the currently visible virtual console
236 (/dev/tty0) will still be used as the system console by default, but
238 "console=ttyCL1".
271 generally being used as a console, we use our own output
276 bool "Support for console on Samsung SoC serial port"
282 an virtual console.
284 Even if you say Y here, the currently visible virtual console
285 (/dev/tty0) will still be used as the system console by default, but
287 "console=ttySACx". (Try "man bootparam" or see the documentation of
302 bool "Support for console on SiRF SoC serial port"
306 Even if you say Y here, the currently visible virtual console
307 (/dev/tty0) will still be used as the system console by default, but
309 "console=ttySiRFx". (Try "man bootparam" or see the documentation of
355 bool "Support console on DECstation DZ serial driver"
361 system console (the system console is the device which receives all
365 Note that the firmware uses ttyS3 as the serial console on
385 bool "Support for console on a DECstation Z85C30 serial port"
391 system console (the system console is the device which receives all
395 Note that the firmware uses ttyS1 as the serial console on the
415 make it the console by answering Y to this option.
417 Even if you say Y here, the currently visible virtual console
418 (/dev/tty0) will still be used as the system console by default, but
420 "console=ttyFB". (Try "man bootparam" or see the documentation of
432 bool "Support for console on Marvell MPSC serial port"
436 Say Y here if you want to support a serial console on a Marvell MPSC.
452 CPU you can make it the console by answering Y to this option.
454 Even if you say Y here, the currently visible virtual console
455 (/dev/tty0) will still be used as the system console by default, but
457 "console=ttySA0". (Try "man bootparam" or see the documentation of
477 CPU you can make it the console by answering Y to this option.
479 Even if you say Y here, the currently visible virtual console
480 (/dev/tty0) will still be used as the system console by default, but
482 "console=ttySA0". (Try "man bootparam" or see the documentation of
587 CPU you can make it the console by answering Y to this option.
589 Even if you say Y here, the currently visible virtual console
590 (/dev/tty0) will still be used as the system console by default, but
592 "console=ttymxc0". (Try "man bootparam" or see the documentation of
606 bool "Support for console on Xilinx uartlite serial port"
611 console (the system console is the device which receives all kernel
633 on your Sparc system as the console, you can do so by answering
649 on your Sparc system as the console, you can do so by answering
662 software console. The following steps need to be completed to use
668 root on this console.)
669 4. Change the kernel command console parameter to: console=ttyB0
672 bool "Support for console on serial MUX"
678 bool "PDC software console support"
682 Saying Y here will enable the software based PDC console to be
683 used as the system console. This is useful for machines in
684 which the hardware based console has not been written yet. The
685 following steps must be completed to use the PDC console:
690 root on this console.)
691 4. Change the kernel command console parameter to: console=ttyB0
706 on your Sparc system as the console, you can do so by answering
713 This driver supports the console device found on SUN4V Sparc
740 bool "Support for console on SuperH SCI(F)"
757 bool "Enable PNX8XX0 serial console"
762 to use serial console, say Y. Otherwise, say N.
775 bool "Enable LPC32XX high speed UART serial console"
780 ports on the LPC32XX as the console, you can do so by answering
820 bool "Coldfire serial console support"
824 Enable a ColdFire internal serial port to be the system console.
866 on your (Power)Mac as the console, you can do so by answering
878 bool "Support for console on CPM SCC/SMC serial port"
883 console (the system console is the device which receives all kernel
886 Even if you say Y here, the currently visible framebuffer console
887 (/dev/tty0) will still be used as the system console by default, but
889 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
894 bool "SGI Altix L1 serial console support"
900 controller serial port as your console (you want this!),
910 for use as console, it must be included in kernel and not as a
919 of the Freescale MPC52xx family as a console.
926 Select the MPC52xx console baud rate.
928 console baudrate
952 bool "use SIO console"
956 Say Y here if you want to support a serial console.
1005 bool "Enable NEC VR4100 series Serial Interface Unit console"
1010 a console on a serial port, say Y. Otherwise, say N.
1051 bool "MSM serial console support"
1062 bool "VIA VT8500 serial console support"
1072 bool "ETRAX FS serial console support"
1093 you can make it the console by answering Y to this option.
1123 console.
1125 Even if you say Y here, the currently visible virtual console
1126 (/dev/tty0) will still be used as the system console by default, but
1128 "console=ttyOx". (Try "man bootparam" or see the documentation of
1155 Support for console and UART on Lantiq SoCs.
1180 Support for console on SCCNXP serial ports.
1273 BCM7xxx (STB) - DOCSIS console
1282 you can make it the console by answering Y to this option.
1296 Support for running a console on the GRLIB APBUART
1305 bool "Altera JTAG UART console support"
1309 Enable a Altera JTAG UART port to be the system console.
1316 Bypass console output and keep going even if there is no
1344 bool "Altera UART console support"
1348 Enable a Altera UART port to be the system console.
1373 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1377 Say Y here if you wish to use the PCH UART as the system console
1378 (the system console is the device which receives all kernel messages and
1398 bool "MXS AUART console support"
1402 Enable a MXS AUART port to be the system console.
1413 bool "Cadence UART console support"
1418 Enable a Cadence UART port to be the system console.
1436 Enable a built-in UART port of the AR933X to be the system console.
1455 bool "EFM32 UART/USART console support"
1529 you can make it the console by answering Y to this option.
1544 SoCs, you can make it the console by answering Y to this option.
1559 bool "Support for console on ST ASC"
1582 bool "Spreadtrum UART console support"
1587 Support for early debug console using Spreadtrum's serial. This enables
1588 the console before standard serial driver is probed. This is enabled
1589 with "earlycon" on the kernel command line. The console is