1152 	mr = BIT_3 | BIT_2 | BIT_1 | BIT_0;  in qla1280_set_target_parameters()
1728 		err = qla1280_mailbox_command(ha, BIT_0 | BIT_1 | BIT_2, mb);  in qla1280_load_firmware_pio()
1800 				BIT_1 | BIT_0, mb);  in qla1280_load_firmware_dma()
1817 				BIT_1 | BIT_0, mb);  in qla1280_load_firmware_dma()
1862 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_start_firmware()
1872 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_start_firmware()
1939 					       BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
1953 						 BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
2173 	status = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_config_bus()
2247 			     BIT_7 | BIT_3 | BIT_2 | BIT_1 | BIT_0);  in qla1280_nvram_config()
2259 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2265 	 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2280 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2289 					  BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2295 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2309 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2313 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2317 	mb[1] = BIT_1;	/* Data DMA Channel Burst Enable */  in qla1280_nvram_config()
2318 	mb[2] = BIT_1;	/* Command DMA Channel Burst Enable */  in qla1280_nvram_config()
2319 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2323 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2329 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2606 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_bus_reset()
2660 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_device_reset()
3781 	else if (pkt->entry_status & BIT_1)  in qla1280_error_entry()
3801 		} else if (pkt->entry_status & BIT_1) {	/* FULL flag */  in qla1280_error_entry()
3978 	qla1280_mailbox_command(ha, BIT_6 | BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_get_target_parameters()