172 		rsi_dbg(ERR_ZONE, "%s: Reset failed : %d\n", __func__, ret);  in rsi_reset_card()
217 		rsi_dbg(ERR_ZONE, "%s: CMD0 failed : %d\n", __func__, err);  in rsi_reset_card()
227 			rsi_dbg(ERR_ZONE, "%s: CMD5 failed : %d\n",  in rsi_reset_card()
240 			rsi_dbg(ERR_ZONE, "%s: CMD5 failed : %d\n",  in rsi_reset_card()
251 		rsi_dbg(ERR_ZONE, "%s: card in not ready : %d %d\n",  in rsi_reset_card()
263 		rsi_dbg(ERR_ZONE, "%s: CMD3 failed : %d\n", __func__, err);  in rsi_reset_card()
277 		rsi_dbg(ERR_ZONE, "%s: CMD7 failed : %d\n", __func__, err);  in rsi_reset_card()
283 		rsi_dbg(ERR_ZONE, "%s: Set high speed mode\n", __func__);  in rsi_reset_card()
286 			rsi_dbg(ERR_ZONE, "%s: CCCR speed reg read failed: %d\n",  in rsi_reset_card()
293 				rsi_dbg(ERR_ZONE,  in rsi_reset_card()
322 			rsi_dbg(ERR_ZONE, "%s: Set bus mode failed : %d\n",  in rsi_reset_card()
391 		rsi_dbg(ERR_ZONE,  in rsi_setupcard()
473 		rsi_dbg(ERR_ZONE, "%s: unable to send ack\n", __func__);  in rsi_sdio_ack_intr()
504 		rsi_dbg(ERR_ZONE, "%s: Synch Cmd53 read failed\n", __func__);  in rsi_sdio_read_register_multiple()
528 		rsi_dbg(ERR_ZONE, "%s: Stopping card writes\n", __func__);  in rsi_sdio_write_register_multiple()
535 		rsi_dbg(ERR_ZONE, "%s: Continue card writes\n", __func__);  in rsi_sdio_write_register_multiple()
546 		rsi_dbg(ERR_ZONE, "%s: Synch Cmd53 write failed %d\n",  in rsi_sdio_write_register_multiple()
589 		rsi_dbg(ERR_ZONE, "%s: Unable to write onto the card: %d\n",  in rsi_sdio_host_intf_write_pkt()
611 		rsi_dbg(ERR_ZONE, "%s: Pkt size is zero\n", __func__);  in rsi_sdio_host_intf_read_pkt()
621 		rsi_dbg(ERR_ZONE, "%s: Failed to read frame: %d\n", __func__,  in rsi_sdio_host_intf_read_pkt()
652 		rsi_dbg(ERR_ZONE, "%s: Failed to enable interface\n", __func__);  in rsi_init_sdio_interface()
666 		rsi_dbg(ERR_ZONE, "%s: Failed to setup card\n", __func__);  in rsi_init_sdio_interface()
674 		rsi_dbg(ERR_ZONE, "%s: Failed to init slave regs\n", __func__);  in rsi_init_sdio_interface()
712 		rsi_dbg(ERR_ZONE, "%s: Failed to init os intf ops\n",  in rsi_probe()
718 		rsi_dbg(ERR_ZONE, "%s: Failed to init sdio interface\n",  in rsi_probe()
724 		rsi_dbg(ERR_ZONE, "%s: Failed in device init\n", __func__);  in rsi_probe()
733 		rsi_dbg(ERR_ZONE, "%s: Failed to request IRQ\n", __func__);  in rsi_probe()
744 	rsi_dbg(ERR_ZONE, "%s: Failed in probe...Exiting\n", __func__);  in rsi_probe()