Lines Matching refs:e_dbg
412 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_reset_hw()
417 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
450 e_dbg("Issuing a global reset to MAC\n"); in e1000_reset_hw()
526 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
562 e_dbg("Error Initializing Identification LED\n"); in e1000_init_hw()
570 e_dbg("Initializing the IEEE VLAN\n"); in e1000_init_hw()
577 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_init_hw()
599 e_dbg("Zeroing the MTA\n"); in e1000_init_hw()
731 e_dbg("EEPROM Read Error\n"); in e1000_setup_link()
755 e_dbg("After fix-ups FlowControl is now = %x\n", hw->fc); in e1000_setup_link()
768 e_dbg("EEPROM Read Error\n"); in e1000_setup_link()
785 e_dbg("Initializing the Flow Control address, type and timer regs\n"); in e1000_setup_link()
903 e_dbg("Flow control param set incorrectly\n"); in e1000_setup_fiber_serdes_link()
913 e_dbg("Auto-negotiation enabled\n"); in e1000_setup_fiber_serdes_link()
931 e_dbg("Looking for Link\n"); in e1000_setup_fiber_serdes_link()
939 e_dbg("Never got a valid link from auto-neg!!!\n"); in e1000_setup_fiber_serdes_link()
948 e_dbg("Error while checking for link\n"); in e1000_setup_fiber_serdes_link()
954 e_dbg("Valid Link Found\n"); in e1000_setup_fiber_serdes_link()
957 e_dbg("No Signal Detected\n"); in e1000_setup_fiber_serdes_link()
975 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_rtl_setup()
991 e_dbg("e1000_copper_link_rtl_setup failed!\n"); in gbe_dhg_phy_setup()
1011 e_dbg("e1000_copper_link_rtl_setup failed!\n"); in gbe_dhg_phy_setup()
1016 e_dbg("Error Resetting the PHY\n"); in gbe_dhg_phy_setup()
1056 e_dbg("Error, did not detect valid phy.\n"); in e1000_copper_link_preconfig()
1059 e_dbg("Phy ID = %x\n", hw->phy_id); in e1000_copper_link_preconfig()
1099 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_igp_setup()
1116 e_dbg("Error Disabling LPLU D3\n"); in e1000_copper_link_igp_setup()
1321 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_mgp_setup()
1355 e_dbg("Reconfiguring auto-neg advertisement params\n"); in e1000_copper_link_autoneg()
1358 e_dbg("Error Setting up Auto-Negotiation\n"); in e1000_copper_link_autoneg()
1361 e_dbg("Restarting Auto-Neg\n"); in e1000_copper_link_autoneg()
1381 e_dbg in e1000_copper_link_autoneg()
1414 e_dbg("Error configuring MAC to PHY settings\n"); in e1000_copper_link_postconfig()
1420 e_dbg("Error Configuring Flow Control\n"); in e1000_copper_link_postconfig()
1428 e_dbg("Error Configuring DSP after link up\n"); in e1000_copper_link_postconfig()
1464 e_dbg("gbe_dhg_phy_setup failed!\n"); in e1000_setup_copper_link()
1480 e_dbg("Forcing speed and duplex\n"); in e1000_setup_copper_link()
1483 e_dbg("Error Forcing Speed and Duplex\n"); in e1000_setup_copper_link()
1505 e_dbg("Valid link established!!!\n"); in e1000_setup_copper_link()
1511 e_dbg("Unable to establish link!!!\n"); in e1000_setup_copper_link()
1553 e_dbg("autoneg_advertised %x\n", hw->autoneg_advertised); in e1000_phy_setup_autoneg()
1557 e_dbg("Advertise 10mb Half duplex\n"); in e1000_phy_setup_autoneg()
1563 e_dbg("Advertise 10mb Full duplex\n"); in e1000_phy_setup_autoneg()
1569 e_dbg("Advertise 100mb Half duplex\n"); in e1000_phy_setup_autoneg()
1575 e_dbg("Advertise 100mb Full duplex\n"); in e1000_phy_setup_autoneg()
1581 e_dbg in e1000_phy_setup_autoneg()
1587 e_dbg("Advertise 1000mb Full duplex\n"); in e1000_phy_setup_autoneg()
1641 e_dbg("Flow control param set incorrectly\n"); in e1000_phy_setup_autoneg()
1649 e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); in e1000_phy_setup_autoneg()
1681 e_dbg("hw->fc = %d\n", hw->fc); in e1000_phy_force_speed_duplex()
1710 e_dbg("Full Duplex\n"); in e1000_phy_force_speed_duplex()
1717 e_dbg("Half Duplex\n"); in e1000_phy_force_speed_duplex()
1727 e_dbg("Forcing 100mb "); in e1000_phy_force_speed_duplex()
1733 e_dbg("Forcing 10mb "); in e1000_phy_force_speed_duplex()
1756 e_dbg("M88E1000 PSCR: %x\n", phy_data); in e1000_phy_force_speed_duplex()
1796 e_dbg("Waiting for forced speed/duplex link.\n"); in e1000_phy_force_speed_duplex()
1824 e_dbg("Error Resetting PHY DSP\n"); in e1000_phy_force_speed_duplex()
2051 e_dbg("Flow control param set incorrectly\n"); in e1000_force_mac_fc()
2094 e_dbg("Error forcing flow control settings\n"); in e1000_config_fc_after_link_up()
2178 e_dbg("Flow Control = FULL.\n"); in e1000_config_fc_after_link_up()
2181 e_dbg in e1000_config_fc_after_link_up()
2199 e_dbg in e1000_config_fc_after_link_up()
2216 e_dbg in e1000_config_fc_after_link_up()
2245 e_dbg("Flow Control = NONE.\n"); in e1000_config_fc_after_link_up()
2248 e_dbg in e1000_config_fc_after_link_up()
2259 e_dbg in e1000_config_fc_after_link_up()
2272 e_dbg in e1000_config_fc_after_link_up()
2277 e_dbg in e1000_config_fc_after_link_up()
2314 e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n"); in e1000_check_for_serdes_link_generic()
2327 e_dbg("Error configuring flow control\n"); in e1000_check_for_serdes_link_generic()
2336 e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n"); in e1000_check_for_serdes_link_generic()
2352 e_dbg("SERDES: Link up - forced.\n"); in e1000_check_for_serdes_link_generic()
2356 e_dbg("SERDES: Link down - force failed.\n"); in e1000_check_for_serdes_link_generic()
2369 e_dbg("SERDES: Link up - autoneg " in e1000_check_for_serdes_link_generic()
2373 e_dbg("SERDES: Link down - invalid" in e1000_check_for_serdes_link_generic()
2378 e_dbg("SERDES: Link down - no sync.\n"); in e1000_check_for_serdes_link_generic()
2382 e_dbg("SERDES: Link down - autoneg failed\n"); in e1000_check_for_serdes_link_generic()
2504 e_dbg in e1000_check_for_link()
2517 e_dbg("Error configuring flow control\n"); in e1000_check_for_link()
2534 e_dbg in e1000_check_for_link()
2593 e_dbg("1000 Mbs, "); in e1000_get_speed_and_duplex()
2596 e_dbg("100 Mbs, "); in e1000_get_speed_and_duplex()
2599 e_dbg("10 Mbs, "); in e1000_get_speed_and_duplex()
2604 e_dbg("Full Duplex\n"); in e1000_get_speed_and_duplex()
2607 e_dbg(" Half Duplex\n"); in e1000_get_speed_and_duplex()
2610 e_dbg("1000 Mbs, Full Duplex\n"); in e1000_get_speed_and_duplex()
2654 e_dbg("Waiting for Auto-Neg to complete.\n"); in e1000_wait_autoneg()
2847 e_dbg("PHY Address %d is out of range\n", reg_addr); in e1000_read_phy_reg_ex()
2875 e_dbg("MDI Read did not complete\n"); in e1000_read_phy_reg_ex()
2881 e_dbg("MDI Read Error\n"); in e1000_read_phy_reg_ex()
2902 e_dbg("MDI Read did not complete\n"); in e1000_read_phy_reg_ex()
2906 e_dbg("MDI Error\n"); in e1000_read_phy_reg_ex()
2985 e_dbg("PHY Address %d is out of range\n", reg_addr); in e1000_write_phy_reg_ex()
3014 e_dbg("MDI Write did not complete\n"); in e1000_write_phy_reg_ex()
3035 e_dbg("MDI Write did not complete\n"); in e1000_write_phy_reg_ex()
3075 e_dbg("Resetting Phy...\n"); in e1000_phy_hw_reset()
3219 e_dbg("Invalid MAC type %d\n", hw->mac_type); in e1000_detect_gig_phy()
3225 e_dbg("PHY ID 0x%X detected\n", hw->phy_id); in e1000_detect_gig_phy()
3228 e_dbg("Invalid PHY ID 0x%X\n", hw->phy_id); in e1000_detect_gig_phy()
3432 e_dbg("PHY info is only valid for copper media\n"); in e1000_phy_get_info()
3445 e_dbg("PHY info is only valid if link is up\n"); in e1000_phy_get_info()
3461 e_dbg("Invalid MDI setting detected\n"); in e1000_validate_mdi_setting()
3715 e_dbg("Could not acquire EEPROM grant\n"); in e1000_acquire_eeprom()
3868 e_dbg("SPI EEPROM Status error\n"); in e1000_spi_eeprom_ready()
3912 e_dbg("\"words\" parameter out of bounds. Words = %d," in e1000_do_read_eeprom()
3999 e_dbg("EEPROM Read Error\n"); in e1000_validate_eeprom_checksum()
4014 e_dbg("EEPROM Checksum Invalid\n"); in e1000_validate_eeprom_checksum()
4033 e_dbg("EEPROM Read Error\n"); in e1000_update_eeprom_checksum()
4040 e_dbg("EEPROM Write Error\n"); in e1000_update_eeprom_checksum()
4086 e_dbg("\"words\" parameter out of bounds\n"); in e1000_do_write_eeprom()
4229 e_dbg("EEPROM Write did not complete\n"); in e1000_write_eeprom_microwire()
4268 e_dbg("EEPROM Read Error\n"); in e1000_read_mac_addr()
4304 e_dbg("Programming MAC Address into RAR[0]\n"); in e1000_init_rx_addrs()
4311 e_dbg("Clearing RAR[1-15]\n"); in e1000_init_rx_addrs()
4471 e_dbg("EEPROM Read Error\n"); in e1000_id_led_init()
4797 e_dbg("Not in Adaptive IFS mode!\n"); in e1000_reset_adaptive()
4835 e_dbg("Not in Adaptive IFS mode!\n"); in e1000_update_adaptive()
5225 e_dbg("Error getting link speed and duplex\n"); in e1000_config_dsp_after_link_change()