Lines Matching refs:on

5 	depends on ETRAX_ARCH_V32 && NETDEVICES
13 	depends on ETRAX_ETHERNET
23 	depends on ETRAX_ARCH_V32
32 	depends on ETRAXFS_SERIAL
38 	depends on ETRAX_RS485
45 	depends on ETRAXFS_SERIAL
48 	  Normally you want this on. You can control what DMA channels to use
54 	depends on ETRAXFS_SERIAL
60 	depends on ETRAXFS_SERIAL
66 	depends on ETRAXFS_SERIAL
72 	depends on ETRAX_ARCH_V32
78          depends on ETRAX_SYNCHRONOUS_SERIAL
83          bool "Enable DMA on synchronous serial port 0."
84          depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
91          depends on ETRAX_SYNCHRONOUS_SERIAL && ETRAXFS
96          bool "Enable DMA on synchronous serial port 1."
97          depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
104 	depends on ETRAX_ARCH_V32
118 	depends on ETRAX_AXISFLASHMAP
121 	  on the boot flash device. When set, mtd0 refers to the whole
126 	depends on ETRAX_AXISFLASHMAP
137 	depends on ETRAX_ARCH_V32
146 	depends on ETRAX_NANDFLASH
154 	depends on ETRAX_ARCH_V32
160 	depends on ETRAX_I2C
166 	depends on ETRAX_I2C
172 	depends on ETRAX_ARCH_V32
187 	depends on ETRAX_GPIO
193 	int "Virtual GPIO interrupt pin on PA pin"
195 	depends on ETRAX_VIRTUAL_GPIO
197 	  The pin to use on PA for virtual gpio interrupt.
201 	depends on ETRAX_GPIO
206 	  user can change direction on using ioctl's.
208 	  You probably want 0 here, but it depends on your hardware.
212 	depends on ETRAX_GPIO
217 	  that a user can change the value on using ioctl's.
222 	depends on ETRAX_GPIO
227 	  that a user can change direction on using ioctl's.
229 	  You probably want 0 here, but it depends on your hardware.
233 	depends on ETRAX_GPIO
238 	  that a user can change the value on using ioctl's.
243 	depends on ETRAX_GPIO
248 	  that a user can change direction on using ioctl's.
250 	  You probably want 0 here, but it depends on your hardware.
254 	depends on ETRAX_GPIO
259 	  that a user can change the value on using ioctl's.
264 	depends on ETRAX_GPIO && ETRAXFS
268 	  that a user can change direction on using ioctl's.
270 	  You probably want 0x00000 here, but it depends on your hardware.
274 	depends on ETRAX_GPIO && ETRAXFS
278 	  that a user can change the value on using ioctl's.
283 	depends on ETRAX_GPIO && ETRAXFS
287 	  that a user can change direction on using ioctl's.
289 	  You probably want 0x00000 here, but it depends on your hardware.
293  	depends on ETRAX_GPIO && ETRAXFS
297 	  that a user can change the value on using ioctl's.
302 	depends on ETRAX_VIRTUAL_GPIO
306 	  that a user can change direction on using ioctl's.
308 	  You probably want 0x0000 here, but it depends on your hardware.
312 	depends on ETRAX_VIRTUAL_GPIO
316 	  that a user can change the value on using ioctl's.
321         depends on ETRAX_ARCH_V32
327        depends on ETRAX_CARDBUS
333 	depends on ETRAX_ARCH_V32
340 	depends on ETRAX_ARCH_V32
347 	depends on ETRAX_ARCH_V32 && MMC
358 	depends on !ETRAX_MMC_IOP
364 # independent of MMC_SPI, so we'll keep SPI non-dependent on the
365 # MMC_SPI config choices (well, except for a single depends-on-line
374 	depends on SPI_MASTER && ETRAX_ARCH_V32
378 	  SPI master controller on Axis ETRAX FS and later.  The
383 	depends on SPI_MASTER && ETRAX_ARCH_V32
387 	  on Axis ETRAX FS and later.  The driver can be configured to
392 	depends on ETRAX_SPI_MMC
399 	  or for devices using the SPI protocol on that port.  Say m if you
405 	depends on ETRAX_SPI_MMC
412 	  or for devices using the SPI protocol on that port.  Say m if you
418 	depends on ETRAX_SPI_MMC
426 	  protocol on general I/O pins.  Slow and slows down the system.