Lines Matching refs:parameter
11 if it doesn't recognize a parameter and it doesn't contain a '.', the
12 parameter gets passed to init: parameters with '=' go into init's
28 Hyphens (dashes) and underscores are equivalent in parameter names, so
46 parameter is applicable:
139 KNL Is a kernel start-up parameter.
140 BOOT Is a boot loader parameter.
151 a trailing = on the name of any parameter states that that parameter will
163 parameter values. These 'K', 'M', and 'G' letters represent the _binary_
225 unusable. The "log_buf_len" parameter may be useful
472 Limit apic dumping. The parameter defines the maximal
476 The parameter valid if only apic=debug or
557 bulk_remove=off [PPC] This parameter disables the use of the pSeries
570 ca_keys= [KEYS] This parameter identifies a specific key(s) on
614 those clocks in any way. This parameter is useful for
755 upon panic. This parameter reserves the physical
824 parameter allows control of the order of pages that will
829 possible value is MAX_ORDER/2. Setting this parameter
843 parameter enables the feature at boot time. In
889 entry later. This parameter disables that.
894 MTRR settings. This parameter disables that behavior,
914 pass the driver to filter for as the parameter.
920 send no or incorrect EDID data sets. This parameter
1069 Using this parameter you can use more than 50% of
1070 your efi variable storage. Use this parameter only if
1095 entry later. This parameter enables that.
1137 parameter will force ia64_sal_cache_flush to call
1144 Warning: use of this parameter will taint the kernel
1154 If no parameter is passed, ftrace will dump
1332 to maximum brightness. If this parameter is set to 0
1333 (default) and the machine requires it, or this parameter
1378 We also add it as printk module parameter, so users
1608 PCI device 00:14.0 write the parameter as:
1615 PCI device 00:14.0 write the parameter as:
1630 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1654 not using this parameter you use sysrq-g to break into
1693 kvm.mmu_audit= [KVM] This is a R/W parameter which allows audit
1768 If only DEVICE is omitted, the parameter applies to
1886 by LOG_BUF_SHIFT kernel config parameter. There is
1887 also CONFIG_LOG_CPU_MAX_BUF_SHIFT config parameter
2023 use. Use this parameter to scan for
2028 seconds. Use this parameter to check at some
2065 Leaving out the screen size parameter will not load
2070 LED. This parameter is not necessary when using the
2081 parameter allows control of the logging verbosity for
2104 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
2126 multitce=off [PPC] This parameter disables the use of the pSeries
2255 parameter to '1'.
2256 The default parameter value of '0' causes the kernel
2306 console_suspend, a printk module parameter to control
2373 xsave to save the states. By using this parameter,
2383 parameter, xsave area per process might occupy more
2663 noaer [PCIE] If the PCIEAER kernel config parameter is
2673 nomsi [MSI] If the PCI_MSI kernel config parameter is
2851 allocator. This parameter is primarily for debugging
3171 rcutorture.shuffle_interval parameter.
3339 If this boot parameter is not specified, only the first
3368 The parameter means the number of CPUs to show,
3494 Note: this parameter cannot be changed while the
3522 controller if no parameter or 1 is given or disable
3544 Ignore sysrq setting - this boot parameter will
3735 anything. Set this parameter to avoid log spamming.
3906 This is actually a boot loader parameter; the value is
4020 The default value of this parameter is determined by