struct nand

struct nand_chip
Prev	Chapter 9. Structures	Next

Name

struct nand_chip — NAND Private Flash Chip Data

Synopsis

struct nand_chip {
  void __iomem * IO_ADDR_R;
  void __iomem * IO_ADDR_W;
  uint8_t (* read_byte) (struct mtd_info *mtd);
  u16 (* read_word) (struct mtd_info *mtd);
  void (* write_byte) (struct mtd_info *mtd, uint8_t byte);
  void (* write_buf) (struct mtd_info *mtd, const uint8_t *buf, int len);
  void (* read_buf) (struct mtd_info *mtd, uint8_t *buf, int len);
  void (* select_chip) (struct mtd_info *mtd, int chip);
  int (* block_bad) (struct mtd_info *mtd, loff_t ofs, int getchip);
  int (* block_markbad) (struct mtd_info *mtd, loff_t ofs);
  void (* cmd_ctrl) (struct mtd_info *mtd, int dat, unsigned int ctrl);
  int (* init_size) (struct mtd_info *mtd, struct nand_chip *this,u8 *id_data);
  int (* dev_ready) (struct mtd_info *mtd);
  void (* cmdfunc) (struct mtd_info *mtd, unsigned command, int column,int page_addr);
  int(* waitfunc) (struct mtd_info *mtd, struct nand_chip *this);
  int (* erase) (struct mtd_info *mtd, int page);
  int (* scan_bbt) (struct mtd_info *mtd);
  int (* errstat) (struct mtd_info *mtd, struct nand_chip *this, int state,int status, int page);
  int (* write_page) (struct mtd_info *mtd, struct nand_chip *chip,uint32_t offset, int data_len, const uint8_t *buf,int oob_required, int page, int cached, int raw);
  int (* onfi_set_features) (struct mtd_info *mtd, struct nand_chip *chip,int feature_addr, uint8_t *subfeature_para);
  int (* onfi_get_features) (struct mtd_info *mtd, struct nand_chip *chip,int feature_addr, uint8_t *subfeature_para);
  int (* setup_read_retry) (struct mtd_info *mtd, int retry_mode);
  int chip_delay;
  unsigned int options;
  unsigned int bbt_options;
  int page_shift;
  int phys_erase_shift;
  int bbt_erase_shift;
  int chip_shift;
  int numchips;
  uint64_t chipsize;
  int pagemask;
  int pagebuf;
  unsigned int pagebuf_bitflips;
  int subpagesize;
  uint8_t bits_per_cell;
  uint16_t ecc_strength_ds;
  uint16_t ecc_step_ds;
  int onfi_timing_mode_default;
  int badblockpos;
  int badblockbits;
  int onfi_version;
  int jedec_version;
  union {unnamed_union};
  int read_retries;
  flstate_t state;
  uint8_t * oob_poi;
  struct nand_hw_control * controller;
  struct nand_ecc_ctrl ecc;
  struct nand_buffers * buffers;
  struct nand_hw_control hwcontrol;
  uint8_t * bbt;
  struct nand_bbt_descr * bbt_td;
  struct nand_bbt_descr * bbt_md;
  struct nand_bbt_descr * badblock_pattern;
  void * priv;
};

Members

IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device
IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device.
read_byte: [REPLACEABLE] read one byte from the chip
read_word: [REPLACEABLE] read one word from the chip
write_byte: [REPLACEABLE] write a single byte to the chip on the low 8 I/O lines
write_buf: [REPLACEABLE] write data from the buffer to the chip
read_buf: [REPLACEABLE] read data from the chip into the buffer
select_chip: [REPLACEABLE] select chip nr
block_bad: [REPLACEABLE] check if a block is bad, using OOB markers
block_markbad: [REPLACEABLE] mark a block bad
cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling ALE/CLE/nCE. Also used to write command and address
init_size: [BOARDSPECIFIC] hardwarespecific function for setting mtd->oobsize, mtd->writesize and so on. id_data contains the 8 bytes values of NAND_CMD_READID. Return with the bus width.
dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing device ready/busy line. If set to NULL no access to ready/busy is available and the ready/busy information is read from the chip status register.
cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip.
waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready.
erase: [REPLACEABLE] erase function
scan_bbt: [REPLACEABLE] function to scan bad block table
errstat: [OPTIONAL] hardware specific function to perform additional error status checks (determine if errors are correctable).
write_page: [REPLACEABLE] High-level page write function
onfi_set_features: [REPLACEABLE] set the features for ONFI nand
onfi_get_features: [REPLACEABLE] get the features for ONFI nand
setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for setting the read-retry mode. Mostly needed for MLC NAND.
chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring data from array to read regs (tR).
options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about special functionality. See the defines for further explanation.
bbt_options: [INTERN] bad block specific options. All options used here must come from bbm.h. By default, these options will be copied to the appropriate nand_bbt_descr's.
page_shift: [INTERN] number of address bits in a page (column address bits).
phys_erase_shift: [INTERN] number of address bits in a physical eraseblock
bbt_erase_shift: [INTERN] number of address bits in a bbt entry
chip_shift: [INTERN] number of address bits in one chip
numchips: [INTERN] number of physical chips
chipsize: [INTERN] the size of one chip for multichip arrays
pagemask: [INTERN] page number mask = number of (pages / chip) - 1
pagebuf: [INTERN] holds the pagenumber which is currently in data_buf.
pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is currently in data_buf.
subpagesize: [INTERN] holds the subpagesize
bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC.
ecc_strength_ds: [INTERN] ECC correctability from the datasheet. Minimum amount of bit errors per ecc_step_ds guaranteed to be correctable. If unknown, set to zero.
ecc_step_ds: [INTERN] ECC step required by the ecc_strength_ds, also from the datasheet. It is the recommended ECC step size, if known; if unknown, set to zero.
onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is either deduced from the datasheet if the NAND chip is not ONFI compliant or set to 0 if it is (an ONFI chip is always configured in mode 0 after a NAND reset)
badblockpos: [INTERN] position of the bad block marker in the oob area.
badblockbits: [INTERN] minimum number of set bits in a good block's bad block marker position; i.e., BBM == 11110111b is not bad when badblockbits == 7
onfi_version: [INTERN] holds the chip ONFI version (BCD encoded), non 0 if ONFI supported.
jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded), non 0 if JEDEC supported.
{unnamed_union}: anonymous
read_retries: [INTERN] the number of read retry modes supported
state: [INTERN] the current state of the NAND device
oob_poi: "poison value buffer," used for laying out OOB data before writing
controller: [REPLACEABLE] a pointer to a hardware controller structure which is shared among multiple independent devices.
ecc: [BOARDSPECIFIC] ECC control structure
buffers: buffer structure for read/write
hwcontrol: platform-specific hardware control structure
bbt: [INTERN] bad block table pointer
bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup.
bbt_md: [REPLACEABLE] bad block table mirror descriptor
badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan.
priv: [OPTIONAL] pointer to private chip data